Choosing the Right System for a New or Replacement AC Installation in Hunters Creek
Building a new home in Hunters Creek, or replacing a system that has finally reached the end of its service life, brings a decision that will affect your comfort and energy bills for the next ten to fifteen years. The air conditioner you install is not a simple appliance swap. It is a carefully sized, precisely matched system that must handle the demanding heat and humidity of Central Florida from spring through late fall. Getting that decision right at the start prevents years of frustration, high utility costs, and premature equipment failure.
At All Pro Cooling and Heating, we approach every AC installation in Hunters Creek as a complete project rather than a quick equipment drop-off. We look at the size and layout of your property, the condition of your existing ductwork, the insulation levels, the window placement, and how your family or business actually uses the space. This attention to detail traces back to the company’s roots. Founded in 2019 by Marcos Ramos with a strong focus on the residential new construction market, and expanded in 2021 through a partnership with Ken Demeiz, who brought deep commercial HVAC expertise, All Pro Cooling and Heating installs systems for custom homes and large commercial builds across the region every week.
How We Size and Select Your New System
The single most common mistake in AC installation is choosing a unit based only on square footage or the size of the old equipment. An oversized air conditioner cools the air quickly but shuts off before it removes enough humidity, leaving your home damp and clammy. An undersized unit runs constantly, never quite reaching the set temperature, and wears out early. Both problems cost you money and comfort. We avoid these outcomes by performing a proper load calculation before we recommend any equipment.
Our load calculation follows the Manual J methodology, which accounts for the specific heat gain of your building. In Hunters Creek, that means we factor in the intense afternoon sun on west-facing walls, the humidity load that Florida homes carry year-round, and the number of people who occupy the space. Once we know the actual cooling demand, we select equipment with the correct tonnage and match the condenser, coil, and air handler as a balanced set. When you choose components that were engineered to work together, you get the full rated efficiency and a longer equipment life.
Efficiency ratings matter in a climate where the air conditioner runs for so much of the year. A few of the key specifications we help you understand include:
- SEER2 rating: This measures cooling efficiency over a full season. Higher numbers mean lower electric bills, which adds up quickly with Florida’s long cooling season.
- Tonnage: This describes the cooling capacity. One ton equals twelve thousand BTUs per hour, and correct tonnage is set by the load calculation, not guesswork.
- Variable-speed and two-stage options: These systems adjust their output to match demand, giving quieter operation, better humidity control, and steadier temperatures throughout the day.
Our Step-by-Step Installation Process
A quality installation is what separates a system that performs to its rating from one that disappoints from day one. Even the best equipment will underperform if the ductwork leaks, the refrigerant charge is wrong, or the drainage is poorly routed. Our installation crews follow a disciplined process on every job so that nothing gets overlooked in the rush to finish.
We begin by protecting your property and removing the old equipment safely, recovering any refrigerant according to environmental regulations. Next, we inspect and prepare the surrounding components. If your ductwork has leaks, crushed sections, or poor insulation, we address those problems before the new system goes in, because a new air conditioner pushing air through leaky ducts wastes a significant portion of the cooling you paid for. We then set the new condenser on a level pad, mount the air handler, and connect the line set with careful attention to slope and support.
The finishing steps are where technical precision truly shows. Our process includes these critical stages:
- Vacuum and leak testing: We evacuate the refrigerant lines to remove moisture and air, then test for leaks before charging.
- Precise refrigerant charging: We weigh in the exact charge specified by the manufacturer, then verify it under running conditions rather than estimating.
- Condensate management: We route the drain line correctly and install safety features to prevent water damage in your ceiling or walls.
- Airflow verification: We measure airflow across the coil and adjust the blower to hit the target range for proper dehumidification.
- System commissioning: We run the complete system, check temperature splits, cycle the thermostat, and confirm every function works before we consider the job complete.
Installations for Homes, New Construction, and Businesses
The needs of a Hunters Creek homeowner differ from those of a new construction builder or a commercial property manager, and we tailor our work to each. For an established home, we often deal with the realities of an existing floor plan, older ductwork, and a preference to minimize disruption. We plan the work so your family spends as little time as possible without cooling, and we clean up thoroughly when we finish. Many homeowners upgrade during a replacement to a higher-efficiency system, and we walk them through the trade-offs so the choice fits their budget and comfort goals.
New construction is where All Pro Cooling and Heating built its reputation. Working alongside builders means installing systems during the framing and rough-in stages, coordinating with electricians and plumbers, and designing duct layouts that fit the architecture from the beginning. Doing this work right during construction pays off for the homeowner for years, since a system planned into the house performs far better than one squeezed in as an afterthought. Our commercial installations bring their own demands, including rooftop units, larger tonnage requirements, and zoning for spaces used in different ways throughout the day. Our team handles all of these applications with the same commitment to doing things right the first time.
Serving Hunters Creek and the Surrounding Communities
Hunters Creek sits within our core service area, and we install and support systems throughout Orlando and the neighboring communities of Windermere, Winter Garden, Lake Nona, Dr. Phillips, Winter Park, Lake Mary, Oviedo, Clermont, Celebration, and Baldwin Park. Our familiarity with the local climate, the common home styles, and the typical challenges of Central Florida properties means we arrive prepared rather than learning on the job. We know how the summer humidity behaves, how much strain the long cooling season places on equipment, and what it takes to keep a system running efficiently in these conditions.
A new installation is also the start of a relationship, not the end of a transaction. After we install your system, we remain available for maintenance, seasonal tune-ups, and support if anything ever goes wrong. Because Florida heat does not wait for business hours, we provide 24/7 emergency service so you are never left without help when you need it most. Whether you are planning a new build, replacing an aging unit, or outfitting a commercial space, our licensed and highly trained team is ready to design and install a system that will keep you comfortable for years to come. At All Pro Cooling and Heating, we don’t just meet standards — we set them, and every AC installation in Hunters Creek reflects that promise.